Autoplay
Autocomplete
Previous Lesson
Complete and Continue
Basic and Advanced Exocad Program
Basic Exocad - Dr Michael Iskander
1.1 Introduction Exocad (0:21)
1.2 Overview On Exocad (2:35)
1.3 Database Of Exocad (11:54)
1.3.2 Material Selection (5:44)
1.3.3 Options And Parameters (4:59)
1.3.4. Database Preparation (8:33)
1.4. Basic Skills In Exocade (8:34)
1.4.2. Crown Buttons (17:52)
1.4-3. Free-Forming (11:35)
1.5. Different Skills In Exocad (10:44)
1.5.2 How To Make The Position Of The Tooth Good (15:41)
1.6. Shrinkage (9:26)
1.7. Summary (1:23)
Inlay,Onlay & Veneers - Dr. Michael Iskander
1.1 Introduction inlay and onlay (0:21)
1.2 Different Module ( inlay and onlay) (11:07)
2.1. Introduction Veneers Module (0:21)
2.2 Different Modules (Veneer) (1:10)
2.3 Design's Steps (12:20)
2.4 Correct Pre-Operative Scan Position (3:29)
2.5 Free-Forming (5:44)
Bridge (Basic Exocad)- Dr. Michael Iskander
1. Introduction-1 (0:22)
2. Different Module In Exocade-2 (6:25)
3. Virtual Articulator-3 (11:07)
4. How To Use The Articulator-4 (3:58)
5. Anatomy Of The Teeth (Simple)-5 (10:13)
6. Anatomy Of The Teeth (Chain Mode)-6 (9:40)
7. Generating Crowns ( The Step Of Free-Forming)-7 (16:59)
8. The Connectors-8 (9:05)
9. Some Tips In Basic Modules-9 (4:17)
Implantology - Dr. Michael Iskander
1. Introduction--1 (4:13)
2. Job Definition--2 (11:03)
3. Detect Implant Position--3 (21:15)
4-Copy And Placement Of The Tooth--4 (3:02)
5. Generate Abutment Buttoms-5 (14:38)
6. Secondary Insertion Direction--6 (12:25)
7. Crown Buttoms--7 (4:06)
8. Customized Abutment Without Scan Body ( Manual Position )-8 (9:46)
9.The Process Of Customized Abutment Manually-9 (15:40)
1. Introduction, Outline And Definition-4 (3:15)
1. Simple Screw Retained Restoration Design 1-1. Introduction-5 (4:59)
1-2. Design 1-2.-1. Design - Material And Positioning--3 (6:02)
1-2-2. Design - Abutment Buttoms And Adjusting The Crown's Emergence Profile, Free Forming Phase, Shrinkage And Multi Level Cut-Back-1 (6:06)
1-2-3. Design - Screw Hole Design Of Single Restoration And Framework-2 (6:06)
2. Full Arch Screw Retained Restoration And Designing Of Virtual Gingiva 2-1. Options And Parameters-14 (9:30)
2-2. Alignment Or Seating And Start Smile Creator--6 (4:27)
2-3. Design 2-3-1. Emergence Profile And Teeth Placement-9 (6:39)
2-3-2. Design - Abutment Butoms, Free Foarming, Distance To Gingiva And Adaptation To Pre-Op Scan-7 (4:49)
2-3-3. Design - Virtual Wax-Up Bottom-8 (4:29)
2-4. Gingival Design-10 (4:36)
2-5. Shrinking-11 (3:49)
2-6. Connectors-12 (2:59)
2-7. Free Forming On Whole Meshwork, Screw Hole Design And Expert Mood Usage-13 (7:24)
2-7. Free Forming On Whole Meshwork, Screw Hole Design And Expert Mood Usage-13
Lesson content locked
If you're already enrolled,
you'll need to login
.
Enroll in Course to Unlock